How are century arms l1a1 receivers marked

#HOW ARE CENTURY ARMS L1A1 RECEIVERS MARKED SERIAL NUMBER#
#HOW ARE CENTURY ARMS L1A1 RECEIVERS MARKED INSTALL#

Everything else is holding up well so far. Only area of noticeable wear has been the tail end of the bolt carrier. Could have been a shaving from the steel case ammo I have been using. Only other thing I noticed was a loose metal splinter in the bolt area.

#HOW ARE CENTURY ARMS L1A1 RECEIVERS MARKED SERIAL NUMBER#

Over the course of dealing with their customer service folks, I determined that mine was manufactured in April of вЂ`15, with a serial number in the 8000 range. I have around 600-700 rounds through mine so far вЂ“ using Tula ammo exclusively вЂ“ and no issues. This is a backup anyway as I elected to replace the OEM sights with Meprolight three-dot tritiums. Only quality issue was a loose front post that I could rotate with a toothpick I contacted CAI and they promptly sent me a replacement. I bought a C39v2 in вЂњZhukovвЂќ configuration this past August. I would bet that my newest Arsenal Rifle the SAM7 84R will outlast my grandkids grandkids if they make it out of one of Hillarys successors mind control camps. I have never HAD to replace a firing pin or extractor but have done so a few times with that old AK variant as a preventive measure. For Arsenal, I have an old Arsenal Bulgaria rifle that I bought before Arsenal had a presence in the USA and that old milled rifle after more cases of steel cased ammo than I can count run through it still runs like a Swiss watch. As long as Arsenal USA and belatedly DDI exist I will simply stick with recommending those companies product lines. I contact Century and I too get treated like shit. I have been an FFL holder for a quarter of a century and I always recommend that my customers avoid Century Arms products and IO products like the plague just from my own past history is trying to get my customers problems corrected since the customer has had no luck they turn to me to see if I can help. Why do people keep giving companies like IO and Century Arms their money? For goodness sake simply DO NOT BUY their products and write them letters telling them that most of their products are sub par and that their customer service sucks at best and until they can PROVE they have changed that you will simply not return to their company. It was very close to the WASR which is impressive. Being chrome lined it was very shinyвЂ¦mirror shiny. One last note, I took a WASR 10/63 with a Chrome lined barrel and ran a barrel light up it. It is of course far more ergonomic like I have it. I just still have guilt for removing all the wood furniture. It should be treated with a lot of respect due to the low light trigger pull and short reset. On the trigger I installed (AKT-S) вЂ¦ I really like it. I would also like to get the factory cerekoting. Once I get this rifle sighted in, IвЂ™m going to purchase a DDI folder with Zhukov handguard in 4150 Ordnance steel milled receiver and 4150 CMV barrel nitrited hopefully with a KrebвЂ™s selector and folding stock. This selector seems to work the best as far as fit, tension, and feel. IвЂ™m probably going to order a selector shelf from Circle 10 and affix it to the Factory selector. Now I just have to shoot it and sight it in using my front sight adjustment tool. I finally topped the rifle of with a QD swivel in the Vltor tube and affixed an Echo 93 FDE sling. I also replaced the factory firing pin with a solid titanium firing pin. I also replaced the archaic pistol grip with a FAB Defense rubberized pistol grip. I replaced the factory brake with a short 3 port SRVV brake. ItвЂ™s a tight fit syncing the Ultimak bands with the Magpul handguard but no dremel work required. I replaced the bottom wood handguard with a Magpul mid length MOE handguard. Up front I replaced the factory gas tube with a Ultimak railed gas tube, ported. I installed a custom fit Limbsaver rubber butt pad. I installed a Vltor rear tube and installed a Magpul CTR stock with a.

#HOW ARE CENTURY ARMS L1A1 RECEIVERS MARKED INSTALL#

I did install a KrebвЂ™s fire control retainer. I tried the tuning but still was not satisfied. They functioned fine but tended to jump the bottom selector stop. I tried both Krebs selectors (MKVI and MKV2). I used a urethane mallet and some support on barrel and moved the sight post enough to have it almost in the middle. I noticed using the laser bore sighter that the point of aim had changed dramatically with the front sight canted far to the right. I had to install a new sight barrel when I installed the tritium sight (a pain). I know MOA is increased but I am setting this up as a close range rifle (SD). I installed a Circle 10 open U-notch rear sight replacement and a front sight with tritium insert. Trigger pull dropped from 6.5lbs to 2.3lbs with very short trigger break and reset. I did not like the trigger and replaced it with the Bulgarian fire control group spring (hammer spring) and an AKT-S fire control group with bow trigger. I must admit I hated to remove the beautiful wood stocks. I purchased a C39V2 late January of this year.

How are century arms l1a1 receivers marked